-
Create an aerogeophysical map filtered from terrestrial geophysics data.
Hello everything is fine? My research group would like to create a 2D map with some specific filters and we are lost where it is possible to execute this in Oasis Montaj. Situation: we have gamma terrestrial geophysics data (K%, eU, eTh) and rock susceptibility. We also have gammaspectrometric and magnetometric…
-
Hi, I am trying to download a new Developer toolkit to work with C#, but links are disabled!
-
Why isn't the Intrusion tool creating a point though a single drill hole lithology contact?
I created an intrusion that should pass through the Light Green/Dark Green contact. It has succeeded with every hole except one. I can see the negative (blue) points are pushing the intrusion upwards. I'm thinking this may be a user error; how can I go about figuring out the problem? The Deposit tool did not have the same…
-
Cut a block model from a pit shell
I have a mesh of an open pit mine and a block model of an orebody that projects vertically outside of the pit mesh. Does anyone know how to cut the block model from the pit shell so that I get an accurate calculation of volume/grade for that particular shape?
-
Drape DTM 2.0 gx
Hi, Does anyone know if the Oasis Airborne QC tool- 'Calculate Draped Survey Altitude' uses the Canadian Geological Survey's Drape DTM v.2.0 gx or algorithm? The CGS's doc for Drape DTM v.2.0 refers to drape_dtm.gx but I cannot find this gx. Just wondering if it is the same tool as found in the Airborne QC extension.…
-
can we filter a block model with a surface?
i would like to find out how many blocks of a block model is above surfaces such as pit shells and/or topography. how can we do this in leapfrog?
-
Importing Oasis grids in to Leapfrog
Hello. I have created some 2D section grids from array data (MASW in this case) using the section tools in Oasis. When I import them in to Leapfrog, I find a pink bounding rectangle around the data. There is no data in the arrays in these regions. Is there some way that I can remove the pink bounding rectangle? Many thanks…
-
What causes a gap in my drillholes when displayed?
-
How to avoid offset of collar labels?
Hi, as you can see in the screenshot below the labels of the collar points are very offset from the actual location. What are possible reasons and how can I avoid this? It's very confusing. Kind regards, Chris
-
Export drill hole trace from Leapfrog Geo
Hi, is anyone knows how to export traces of drill hole from Leapfrog Geo ? I need Shapefile or DXF or equivalent. regards
-
Is there a way in Leapfrog to know the average thickness of the layers in the model?
Is there a way in Leapfrog to know the average thickness of the layers in the model?
-
How can i edit blank spaces in a volume of a geological model?
I created a geological model from meshes that i created from a set of xyz points. Because they did not have the same distance between them, there are some blank spaces in the volume that was created like the one on the picture and in the limits of each unit: How can i fixed that?
-
Lateral extents from distance in vein system
Hello, Does anyone know if there is any way to apply diferent latteral extent from distance to diferent veins at vein system? I can only apply it to the whole boundary. Thanks.
-
Calculating depth array from elevation array
Hello. At some point in the past I recall being able to calculate a depth array using channel maths by subtracting the elevation array channel from the ground surface elevation. This doesn't seem to work today. Does anyone know if i imagined this or if it is possible now? Many thanks Tim
-
How to fix the following errors:
This surface is non-manifold, its inside can not be distinguished from its outside so its use within your project will be limited. This mesh has self-intersecting triangles.
-
Luminiscence Images
Tengo Imagenes de luminiscencia que fueron tomadas a las cajas de los barrenos, y quiero cargarlas en imago de manera que se visualicen a lo largo del barreno, podran apoyarme con el procedimiento? Saludos Miguel
-
Different factors of safety
Hi there, I have problem with slope stability calculations of tailing dam. I carried out the calculation with the use of different methods and I got the resulting factor of safety as follows: 1.74 for Morgenstern-Price method 1.51 for stress based method 1.4 for strength reduction method Why theses results are so different…
-
Best way to limit the areas new data can modify implicant model boundaries.
Hi, I was wondering if anyone had a solution or work through to limit the area new data can change the implicant model. When completing infill in say an Inferred area and you update the model and the hanging and footwall changes with the new data, this modification can often extend into the indicated part of the domain,…
-
How to limit river deposits to the river bed
Hi all I'd like to know how I can limit the extent of river deposits (soft formation) to their river bed in a valley with steep slopes. I tried using their mapped contours as his or polylines with and without tangent but the results are not what is to be expected: the base of river deposits extends into the valley slopes,…
-
Free arcgis pro addin
Hi everyone, I need assistance to locate the free arcgis pro addon . It is described both in website and support but i cannot seem to find it. can anyone provide me with the link if there is any ? I need it to open grids within arcgis pro Cheers
-
Python initialization failed
Hi all, Trying to run Python scripts within OM, I constantly get the following error: It's strange since I can successfully verify Python and use geosoft Python library in any IDE outside OM. Regards, Artem
-
Is therea way in Leapfrog to represent lithologies intersecting a pit wall? I done see a way to Eval
-
GX to set a colour ramp
Hi! I have some ITRs that I am repetitively setting to a map in line with some daily work I am performing. Is there a GX that I can add in to my gridding script that can automate this process? I've had a look at various help documents etc and have come up with no answers so thought I'd ask here!
-
adding prefixes or other text onto cross section layouts
Hello, Does anyone have a workflow for adding text "prefixes" to borehole data displaying on a cross section layout? I've been looking into calculation fields, but without much luck. For context, I want my cross section N values to say "N=" to the left of the data. For instance in the image below I'd like it to say N=11.0…
-
Assigning Attributes to Volumes - Leapfrog works 2021.2
How does the assignment of attributes to volumes work in lepfrog 2021.2? is it possible to download a leapfrog 2021.2 manual? Thanks.