-
Recreating models & topographies in the new version of Visible Geology
Hi everyone! 👋 I wanted to kick off a discussion thread about recreating models and topographies in the new version of Visible Geology. If you haven't already, you can use the beta version here to test and respond! As per the FAQs (found here) work saved in the old version of the application will not be migrated. Our aim…
-
User-defined Constitutive model in Geostudio SIGMA/W
Dear all, Is it possible to implement a user-defined constitutive model into Geostuido SIGMA/W? If yes, then what programming language is supported? Are there any examples for reference? I'd appreciate it for your help. Regards Chou.
-
How to control the initial saturation degree in transient analysis
Hello. I'm conducting a transient analysis to simulate the infiltration of runoff into a sump, but I'm encountering convergence issues. Despite trying all the suggestions from here, here and here , I continue to see red crosses in few steps (day 45-48). Upon reviewing my model, I noticed that the transition in saturation…
-
Geological Model
Hello, is it possible convert lithology into number? e.g i have a 30m granite from 0m to 30m and i would like to code GRANITE as "1" so that instead of granite it will "1" in new calculation column but the result will be 0-1m=1, 1-2m=1,………29-30=1m?
-
Installation Failed
Dear all, @BeckyBodger are you there? :-) I am unable to install the Geosoft Oasis Montaj 9.6 Setup 98 2019 on a PC with W11 22H2. The system gives me the following error message during the install process: "Failed to download: http://updates.geosoft.com/Prereq/VCRuntime/VC2005.exe ". I tried to reach updates.geosoft.com…
-
Can someone help me with the drawing of this section?
Its a drill, was a question from my Genesis test… I (So=180/15) = V (So=010/60) = succession of carbonaceous siltstones, sandstones, limestones, rhyolites, and ignimbrites. II=IV (S=175/70) = rock composed of kaolinite + quartz + pyrite with structural Au (gold). III (S=175/70) = rock composed of vuggy quartz +…
-
Latest User Manual for Leapfrog Works
Can someone please help me with the latest Leapfrog works User Manual. I were able to find the 2020 version (Version 3.1) on google but it seems quite outdated.
-
E994 Error Soil Nail Design
Hi, I'm working on a soil nail design. We used fully specified method, and I have encountered E994 error in a few of the slip surface's FOS. I am not entirely sure if I can change the slip surface. Anyone has an idea to fix this other than redrawing/tweaking the slip surface? I tried changing the drillhole dia, bond…
-
Import a 3D photogrammetry model into LF
Hello, I’m trying to import a 3D model from Agisoft Metashape (photoscan) to LF. I’ve tryed to import the dense cloud points and asign the colors to each point but it didn’t work. I’ve uploaded a obj model as a mesh, it is loaded but I cant import the texture. Apparently only ireg files (texture vulcan format) can be…
-
Exporting mesh texture
Hi all, I have two projects: 1) my main project with lots of data and several geological models and 2) a mini-project with just one mesh with a photo compilation of drone imagery aka "mesh texture. Can I export the mesh *with* the texture from project 2 and import into project 1?
-
Borehole collar elevation
Hi currently i trying to simple geological model based on cptu data and when layouting the long section i noticed that z elevation for borehole doesnt match the GM. any idea how to make it match?
-
3D printing geological models tips and tricks
I wanted to drive a little discussion about 3D printing your models and ideas / tips on settings and edits needed to make it work. The below picture is a vein model (or part of) that I increased the thickness on and restricted what volumes where included to make the printing go easier. Then I exported that out as a OBJ…
-
Export
Hello, is it possible to export only ignored collar data?
-
Planned Drillholes
Hi, I started a formation on "Planned Drillholes" menu but I can't find it anymore in the Learning Catalogue. Do someone have the link please. Thanks!
-
Can you back flag new assay data to Block model?
Looking to evaluate our new assays from drilling against our resource block model. Im pretty sure I have done this in the past but years ago? Basically looking to back flag the new drill holes and assays to the block model to quickly evaluate gains and losses through this campaign of drilling However can only evaluate…
-
Coincident Faults error on Fault System
Hi, When I whant to apply a "Fault System" I get a "Coincident Faults" error as shown on the image. The fault as the same boundary coordinates as the GM. Any idea what could cause the problem? Thanks you!
-
How to create a geological model of coal case study in leapfrog?
Hi guys, Can you help me, how is the geological modeling of coal case study, what type of surface chronology is used to model coal. Thank you for your help
-
Layout Templates are completely useless?
Hello, did anyone successfully use the Layout Template feature? I need to create 15 cross sections from polylines and wanted to implement the Layout template feature instead of copying a single layout to multiple sections again every time I make a minor change. But the cross sections, being at different locations, do not…
-
Initial Resources estimation by LF GEO
Has anyone done block modelling on LF Geo, if so, what was the initial estimate, good or bad? What is the challenge and what steps would you suggest I focus?
-
Import BM csv form
"The rest of the file was not loaded" it is from leapfrog. how i can decide?
-
DTM 2.0 - Error
Getting error pop-ups while using DTM 2.0 available at https://ostrnrcan-dostrncan.canada.ca/entities/publication/dd8ee1f5-5819-4b33-8193-96d7ed9b3266 Errors are attached below. Am I missing something?
-
Adding Support for Compressed Geosoft Grid Files
Hello, I am looking for info of how to add support for importing / exporting Compressed Geosoft Grid Files into a third party C++ application. What are the code / repositories / libraries / docs / specs I should be looking at to provide support for importing / exporting these types of files (.grd)?
-
inquiry about LF and Databricks integration
I am writing to inquire about potential integrations or experiences with LF and Databricks. I am particularly interested in knowing if there are any LF users who have successfully implemented LF directly on Databricks or utilized Databricks as an archive for LF zipped projects. If such cases exist, I would be grateful for…
-
Is it possible to have a vein layer as top layer?
I've developed a Leapfrog model to analyze the stability of a tailings dam. The model represents two top green layers as tailings, which have been modeled as vein. The underlying purple layer is sediments, modeled as a deposit. In the model, the tailings (modeled as vein) are expected to form the top layer. However, the…
-
Where can I find more python extension examples ?
I am creating an extension using python. I am using the documentation https://geosoftgxdev.atlassian.net/wiki/spaces/GXD20212/pages/2479588080/Reference and api reference: https://geosoftinc.github.io/gxpy/2021.2/python/geosoft.gxpy.html But I haven't found a place where I can see more comprehensive examples. Are there…